Staleks Expert Carbide Bit Corn fine

STALEKS EXPERT Carbide bit corn shape red – Ø 5 mm, working part 13 mm

The STALEKS EXPERT carbide corn bit (red) is a professional bit for hardware manicures and pedicures. The characteristic corn shape, a diameter of 5 mm, and a 13 mm long working part make it particularly versatile for working on artificial materials as well as for selected applications on calloused skin.

The red marking indicates a soft grit. The carbide bit was developed, among other things, for correcting extended nails, removing gel polish and hard coatings, and treating calluses and corns.

Staleks item number: FT90R050/13

Corn bit for artificial nails and coatings

The special corn shape allows for efficient and controlled removal of artificial material. The bit can be used to remove coatings, correct artificial nails, and prepare nails for a new set.

The carbide bit cuts the material cleanly, leaving an even, smooth surface. It is particularly suitable for professional applications that require precise material correction.

Suitable for

• Removal of gel polish and hard coatings

• Removal of artificial materials

• Correction of extended nails

• Shaping of artificial nails

• Correction of the nail plate

• Removal of excess material

• Preparation of natural nails for re-coating

• Treatment of calloused skin areas

• Treatment of corns and calluses

Fine shavings instead of dust

A special feature of this STALEKS carbide bit is that it removes material in the form of fine shavings rather than dust. According to the manufacturer, this is particularly advantageous for pedicure and podiatry applications.

This makes the bit suitable not only for nail modeling but also for specific work on hardened and calloused skin areas.

Versatile in manicure, pedicure, and podiatry

The STALEKS EXPERT corn bit can be used in both hardware manicures and professional pedicures.

For nail work, it assists in correcting artificial nails and efficiently removing coatings. In foot care, it is suitable for treating calloused skin, corns, and calluses.

This makes the bit a versatile addition for nail salons, beauty studios, and professional foot care clinics.

High-quality carbide bit for professional use

According to the manufacturer, the STALEKS EXPERT carbide bit is made of high-quality metal and is corrosion-resistant. The design is intended for continuous professional use.

The bit is suitable for various types of disinfection and sterilization, provided that the prescribed procedures, manufacturer instructions, and certified agents are followed.

Your benefits at a glance

• Professional STALEKS EXPERT carbide bit

• Practical corn shape

• Red marking – soft

• For hardware manicures and pedicures

• For removing gel polish and hard coatings

• For artificial and extended nails

• For correction and shaping of artificial nails

• For treating calloused skin

• Suitable for corns and calluses

• Material removal in fine shavings

• High-quality metal

• Corrosion-resistant

• Suitable for disinfection and sterilization
  

Using the carbide corn bit

Insert the bit according to the operating instructions of the nail drill used. Depending on the intended application, it can be used to remove artificial coatings from the nail plate, shape and correct artificial nails, remove excess material, and prepare natural nails for re-coating.

Furthermore, the bit can be used for polishing hardened skin in the nail plate area. Remove the bit from the device after use.

Important: The speed recommended by the device manufacturer must be strictly observed. Using it at too high a speed can lead to injuries, especially during manicures.

Cleaning, disinfection, and safety

The carbide bit should be stored in a dry, well-ventilated place, out of the reach of children, and at least 1 meter away from heating appliances. The manufacturer recommends storage at 0 to 40 °C and a relative humidity of up to 80%.

No acids or alkalis may be used for disinfection and sterilization. Likewise, abrasive or metallic objects are not permitted for cleaning. The bit should be protected from dropping onto hard surfaces and from contact with corrosive substances.

STALEKS EXPERT bit – efficient work with artificial materials

The STALEKS EXPERT carbide bit red Ø 5 mm with a 13 mm working part is a professional solution for the efficient processing of artificial nails and hard coatings. Its corn shape allows for controlled material removal and supports the correction, shaping, and preparation of artificial nails.

Additionally, the bit is suitable for specific applications in pedicures and podiatry, for example, for treating calluses, corns, and other calloused skin areas. With its robust construction, corrosion-resistant design, and suitability for disinfection and sterilization, it is a practical addition to any professional toolkit.